At present almost all mobile phone operators in the country providing internet services, we just choose which operator you want .. . This post will not discuss the choice to choose an ISP (Internet Service Provider), but how or tricks to increase / stabilize the 2G or 3G signal, so we are more stable internet access.I had always made annoyed because HSDPA signal from the service that I use always arise tengelam and even disappear .. maybe because it is far from the internet BTSnya.sehingga often slow or often broken.When this problem was not the case anymore because the signal is always full bars .. HSDPAnya although I was in a closed room wall or in a room that usually do not get a signal ..What I do is put the modem is far above, in a more open area that is outside the home, on the second floor roof .. makes the signal strong and stable caught, do not arise again submerged.The way used is to extend the USB cable modem .. to 12 (twelve) meters (standard 1 or 1.5 meters), this is against the theory that he said was the maximum USB cable length is about 5 meters. but in reality its length plus .. CAN.
Maybe this will depend on the type of cable used, brand / type of modem, and power of computer power usb port.Modem that I use is the Huawei E270 .. even before when using a modem Huawei EC325 (CDMA) reaches 15 meter long cord, and when the cable is used to huawey E270 modem, the modem is not detected then reduced and reduced length of the cord so that the range of 12 meters length E270 modem is functioning properly.How do I dial?, What kind of cable is used?1. Prepare a standard USB cable (USB cable into the modem) of good quality.2. Prepare the UTP cable (unshielded twisted pair, is the standard cable for computer network connections
LAN), cat 5 or cat 6 is better, eg 12 meters in length is adjusted first (12 m do not necessarily match the
modem you will probably have to be reduced in length)
3. Tools for grafting: Solder, tin, insulation, scissors / pliers cutters
How workmanship
1. Cut (for two) USB cable modem, then peel each end. USB cable in it has 4 wires plus 1 ground (ground
wires will not be used, because of the limited amount of content UTP cable)
2. Prepare the UTP cable, peel the ends. UTP cable has eight wires inside the content. Because the USB
cable contains 4 wires, then we only need 4 UTP cable content, but in order to increase the conductivity
(reduce resistance) every two wires coupled / fixed, so as if this UTP cable contains 4 wires.3. Connect the USB cable with UTP cables, note the color of the cable should not be confused, solderlah
each connection then give isolation.
Selecting and determining the color of UTP cable-free, the important color at the end of the USB cable that one should meet again with the same color on the other end, a USB cable red color should be reunited with the red wire, black must see black and so on .. should not be confused .. if not, could be a modem or even damaged USBnya port ..
to prevent konsleting.
not be exercised. because if the connection is not right to cause the computer (USB port) or modem is
damaged. if you still do not understand or try asking for help to friends who know about electronics.
if you are absolutely sure, please try, turn on the computer and connect the modem, if your modem is detected by the computer means to stay put the modem in the best area to receive the signal. If not detected or USB malfunction, then the cord should be made even shorter .. Once the modem is found to be useful, then place the modem in an area that if the strongest signal from the operator.
That must be considered:Be careful of the dangers of lightning, when it's cloudy and we are not sure of the lightning rod building / house .. Just lower the betterPlace in areas that do not get direct sunlight.Be careful also to rain .. if ya got the rain ended the ...
In the application can also be used to place the modem in a vehicle, of course with a shorter cable connection .. 5. Check again, if you are sure the connections are correct, the new can be tried, if not yet convinced should 4. To be a strong connection between the cable and good connections, solderlah well then give the insulation
Maybe this will depend on the type of cable used, brand / type of modem, and power of computer power usb port.Modem that I use is the Huawei E270 .. even before when using a modem Huawei EC325 (CDMA) reaches 15 meter long cord, and when the cable is used to huawey E270 modem, the modem is not detected then reduced and reduced length of the cord so that the range of 12 meters length E270 modem is functioning properly.How do I dial?, What kind of cable is used?1. Prepare a standard USB cable (USB cable into the modem) of good quality.2. Prepare the UTP cable (unshielded twisted pair, is the standard cable for computer network connections
LAN), cat 5 or cat 6 is better, eg 12 meters in length is adjusted first (12 m do not necessarily match the
modem you will probably have to be reduced in length)
3. Tools for grafting: Solder, tin, insulation, scissors / pliers cutters
How workmanship
1. Cut (for two) USB cable modem, then peel each end. USB cable in it has 4 wires plus 1 ground (ground
wires will not be used, because of the limited amount of content UTP cable)
2. Prepare the UTP cable, peel the ends. UTP cable has eight wires inside the content. Because the USB
cable contains 4 wires, then we only need 4 UTP cable content, but in order to increase the conductivity
(reduce resistance) every two wires coupled / fixed, so as if this UTP cable contains 4 wires.3. Connect the USB cable with UTP cables, note the color of the cable should not be confused, solderlah
each connection then give isolation.
Selecting and determining the color of UTP cable-free, the important color at the end of the USB cable that one should meet again with the same color on the other end, a USB cable red color should be reunited with the red wire, black must see black and so on .. should not be confused .. if not, could be a modem or even damaged USBnya port ..
to prevent konsleting.
not be exercised. because if the connection is not right to cause the computer (USB port) or modem is
damaged. if you still do not understand or try asking for help to friends who know about electronics.
if you are absolutely sure, please try, turn on the computer and connect the modem, if your modem is detected by the computer means to stay put the modem in the best area to receive the signal. If not detected or USB malfunction, then the cord should be made even shorter .. Once the modem is found to be useful, then place the modem in an area that if the strongest signal from the operator.
That must be considered:Be careful of the dangers of lightning, when it's cloudy and we are not sure of the lightning rod building / house .. Just lower the betterPlace in areas that do not get direct sunlight.Be careful also to rain .. if ya got the rain ended the ...
In the application can also be used to place the modem in a vehicle, of course with a shorter cable connection .. 5. Check again, if you are sure the connections are correct, the new can be tried, if not yet convinced should 4. To be a strong connection between the cable and good connections, solderlah well then give the insulation